Driver configuration. Download PLC program

Download the program to PLC or PLC emulator is done in two stages. The first stage is to configure the communications driver RSLinx. The second stage is the download from RSLogix to the PLC.

Communication driver configuration

1.Open RSLinx and click Configure Drivers of Communications menu.

Configure drivers

Configure drivers

2. Click on the arrow of Available Driver Types and select the driver. The SLC 500 (DH485) Emulator driver is chosen to download to RSEmulate500. Then click the AddNew button.

Select driver

Select driver

3. A dialog box that asks for the name you want to give to the driver is shown. Leave the default name and click OK.

Driver name

Driver name

4. A dialog box asking the address and name of the station where RSLinx is running is shown. Leave the defaults and click OK.

Station number

Station number

After following these steps, the driver should appear in the list of drivers configured with a status of Running.

Close RSLinx (no shutdown) the driver stays running as a service.

RSlinx as a service

RSlinx as a service

Download the program from RSLogix.

With the program you want to download open on the RSLogix, follow these steps:

1. Double-click the Controller Properties folder in the browser window.

Controller properties

Controller properties

2. Controller Communications tag is selected. Click the driver arrow and select the driver to be used for downloading. Select EMU500-1 for use with RSEmutae500. Default processor address is 1, only must be changed if it are using a different address. Then click on OK.

Select driver. RSLogix

Select driver. RSLogix

3. Click on the arrow of Program / Processor Status and select Download (or Download option in the menu Comms).

Download Program

Download Program

4. If there is a program in memory of the processor or emulator a confirming of the download is requested, press OK. In another case this confirmation is not displayed.

Confirm download

Confirm download

5. RSEmulate will open, minimize it.

RSEmulate 500

RSEmulate 500

6. In RSLogix a dialog box is displayed asking if you want to go online, click OK. The ladder in the Program / Processor Status bar will begin to turn.

go online

go online

7. Finally click on the arrow in the Program bar / Processor Status and select the run

Run mode

Run mode

Downloading repeatedly

The driver in RSLinx and RSLogix are configured once. When you want to download the program after modifying it, the procedure is as follows.

  1. Verify program
  2. Save program
  3. Download program
  4. go online
  5. Switch to run mode

7 Comments

  1. Pingback: PLC: my first steps - Control Real English

  2. hewa

    Hello Dear
    please tell me how I solve my problem in ab micrologix ,when I want to use SLC 500 (DH485)
    no containg in driver dialog box How I can to add this new protocol .
    Regards

    Reply
    1. Miguel

      Hello Hewa, I apology for my late answer, You message went to the folder span. There are three drivers for DH485 protocol, the most common is “DH485 UIC Device” (you need 1747-UIC interfaz, do not work with usb to RS232 interface), The other two driver are”1747 PIC/AIC+ driver” (you need a 1747 pic, a 1747 AIC or a 1761-NET-AIC+) and “1784-PKTX(D)/PCMK for DH+/DH device” (you need 1784-pcmk which is obsolete).

      Reply
  3. ROWELL ENGINEER

    CLICK SKIP AD

    Reply
  4. Ganesh

    SLC 500 DH 485 DRIVE NAME NOT AVAILABLE IN AVAILABLE DRIVE TYPE HOW TO ADD THIS DRIVE THERE TO SELECT IT AND MOVE FORWARD

    Reply
    1. Miguel

      You have probably downloaded a version of RSlinx that is not compatible with your operating system, try a lower version of RSLinx

      Reply
  5. arshid

    is this software compatible at window 10 64bit
    also with micrologic 1500 plc

    Reply

Leave a Comment

Your email address will not be published. Required fields are marked *